What We Can Insulate - Insulation for Brick Walls & More

No matter what your home is constructed of, we can help - our USA Premium Foam insulation can be used in brick, block, stucco, shingle and wood houses, in addition to houses with vinyl or aluminum siding. Plus, it also provides an effective moisture and thermal barrier in basement walls.

We Can Insulate Where Others Cannot

Wood and Steel Stud Walls Brick/Veneer Masonry CMU Block Applications
USA Premium Insulation Yes - READ MORE > Yes - READ MORE > Yes - READ MORE >
Cellulose Yes (Injected into cavity - slow process) No No
EPS Board Yes (Nailed to studs after wall torn out ) No Yes (Nailed to studs after wall torn out )
Fiberglass Batting Yes (Reinstalled after after wall torn out ) No No
Polyurethane Spray Foam Yes (Sprayed on after after wall torn out ) Yes (Sprayed on after after wall torn out ) Yes
Spray Foam House Insulation Spray Foam House Insulation Spray Foam House Insulation Foam Insulation

Wood and Steel Stud Walls

USA Premium Foam is ideal for use in both interior and exterior wood frame load bearing wall systems, as well as steel or wood stud party wall partitions. Installed in a standard 2" X 4" wood frame wall, and covered with a single layer of 1/2" gypsum board, USA Premium Foam will provide an R-value of 21.4 and an STC rating of 53. In redundant testing, a standard interior wall constructed of 2" X 4" wood studs and covered with a single layer of 1/2" gypsum board normally fire-rated at 1/2 hour, and was increased to 1 and 1/2 hours with the installation of USA Premium Foam.

In similar E119 testing, USA Premium Foam had more than doubled the fire-hour ratings on load bearing wall systems, and increased ratings on steel stud walls by over 50%. Independent laboratory tests demonstrate that USA Premium Foam far surpasses the fire performance of any urea formaldehyde type foam, polyurethane, or glass fiber product. USA Premium Foam provides an upgraded fire-hour rating without costly additions of double layer gypsum board.

Brick/Veneer Masonry

USA Premium Foam can be foamed-in-place between the brick veneer and cement blocks during a retrofit application. The application is done by drilling a 5/8 inch hole in the mortar, between the brick/block. The Foaming hose is reduced to a 5/8 inch tube and the foam is injected in the wall. As soon as the cavity is filled, it can be patched with the dyed-matched mortar. The foam reduces infiltration and fills all voids and cracks while easily flowing around all obstructions. It is considerably less expensive than rigid types of insulation. Foundations on homes are insulated by the above process.

CMU Block Applications

The USA Premium Foam system for masonry block core-fill is the most cost-effective way to increase the thermal performance of this type of construction. The total thermal resistance is more than doubled over conventional insulations. USA Premium Foam products can be easily and efficiently installed in new or existing masonry construction, either during construction or upon completion by a pressure fill method. USA Premium Foam meets the mandatory requirements and codes for heat loss factor (U value) for wall structures adopted by many State and Federal Agencies. It is important to note that the heat loss is reduced through the mortar joints as well as the block. This is not the case with block inserts. The USA Premium Foam system is more cost-effective than core inserts or pour-in products.

Attic Insulation

USA Insulation uses Fiberglass or Cotton insulation in all our Attic work. Johns Manville blow-in, loose-fill fiber glass insulation is designed for attics and hard-to-reach locations like corners, nooks and crannies. It is non-corrosive and noncombustible. Climate Pro is for professionals using large truck-mounted high volume production blowing wool machines. Read More >

Trying to Decide Whether to Insulate Your Home? Click Here to Calculate Your Savings
Spray Foam House Insulation
"We had three homes, and all three were insulated by USA Insulation. It's the best thing we have ever done. If we ever have to move we would do it again with USA Insulation."

Mr. & Mrs. Peck


This information is not intended as an offer to sell, or the solicitation of an offer to buy, a franchise. It is for information purposes only. Currently, the following states regulate the offer and sale of franchises: Illinois, Indiana, Kentucky, Maryland, Michigan, Missouri, Nebraska, New Jersey, New York, North Carolina, Ohio, Pennsylvania and Virginia. If you are a resident of or want to locate a franchise in one of these states, we will not offer you a franchise unless and until we have complied with applicable pre-sale registration and disclosure requirements in your state.

USA Insulation is a registered trademark of USA Insulation LLC

Copyright © 2015. USA Insulation, All Rights Reserved. All USA Insulation Franchise Locations Are Independently Owned And Operated